extron ipcp pro 555q  xi

Extron IPCP PRP 555Q xi 

IPCP Pro 555Q xi

Memory

SDRAM

2 GB


Flash

8 GB


Software

Configuration software

Global Configurator® Plus and Professional


Programming software

Global Scripter®


Control apps

Extron Control


Resource management software

GlobalViewer® Enterprise


Utilities

Toolbelt, embedded web page


Hardware user interface

Hardware

TouchLink® Pro touchpanels, Network Button Panels, or eBUS® button panels


USB — Ethernet over USB

USB configuration port

1 front panel female USB Type-C® for local configuration


USB standards

USB 2.0, high/full/low speed host


Protocols

ECM, IPv4, RNDIS, USB suspend


Default settings

IP address = 203.0.113.22

Subnet mask = 255.255.255.248

Gateway = 0.0.0.0


Ethernet

Network interface controllers (NICs)

2: 1 LAN, 1 AV LAN


Connectors

2 female RJ-45 connectors


Data rate

10/100/1000Base-T, half/full duplex with autodetect


Protocols

DHCP, DNS, HTTP, HTTPS, ICMP, IEEE 802.1X, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP


Default settings

LAN

Link speed and duplex level = autodetected

IP address = 192.168.253.250

Subnet mask = 255.255.255.0

Gateway = 0.0.0.0

DHCP = off

DNS = 127.0.0.1

AV LAN

Link speed and duplex level = autodetected

DHCP server = disabled

Subnet mask = 255.255.255.0

Gateway = 0.0.0.0

DHCP server disabled

IP address = 192.168.254.250

DNS = 127.0.0.1

DHCP server enabled

IP address = 192.168.254.1

DNS = 192.168.254.1

Dynamic leased IP address pool = 192.168.254.100 - 192.168.254.149

Maximum lease count = 50

Lease time = 24 hours


Serial

Quantity/type

2 bidirectional RS-232, RS-422, RS-485 (ports 7 and 8)

6 bidirectional RS-232 (ports 1 through 6)


Connectors

(2) 3.5 mm captive screw connectors, 5 pole

(6) 3.5 mm captive screw connectors, 3 pole


Baud rate and protocol

300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;

no parity (default), even, or odd parity


Pin configurations

Serial, 5-pole captive screw

RS-232 (default)

Pin 1 = Tx, 2 = Rx, 3 = Gnd, 4 = RTS, 5 = CTS

RS-422

Pin 1 = Tx-, 2 = Rx-, 3 = Gnd, 4 = Tx+, 5 = Rx+

RS-485

Pins 1 and 2 (tied together) = data-, 3 = Gnd, 4 and 5 (tied together) = data+

Serial, 3-pole captive screw

Pin 1 = Tx, 2 = Rx, 3 = Gnd


Flex I/O

Quantity/type

4 analog input or digital input/output (configurable)


Connectors

(1) 3.5 mm captive screw connector, 5 pole


Digital inputs

Input voltage range

0 to 24 VDC, clamped at +30 VDC


Input impedance

29k ohms


Programmable pullup

1k ohms to +5 VDC

Threshold low to high


Programmable range: 100 mV to 24 VDC, default = 2.4 VDC

Threshold high to low

Programmable range: 100 mV to 24 VDC, default = 0.8 VDC


Digital outputs

250 mA sink from 24 VDC max.


Analog inputs

12 bit A/D, 0 to 24 VDC


Pin configurations

1, 2, 3, 4 = flex I/Os 1, 2, 3, 4; 5 = Gnd


IR/serial

Quantity/type

8 programmable: unidirectional RS-232 (±5 V), or TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz


Connectors

(4) 3.5 mm captive screw connectors, 4-pole


Baud rate and protocol (RS-232)

300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;

no parity (default), even, or odd parity


Pin configurations

For each port, pin 1 = signal, 2 = Gnd

IR output carrier frequency

30 kHz to 300 kHz

IR learning carrier frequency

30 kHz to 300 kHz


IR learning capture distance

2" (5.1 cm) to 12" (30.5 cm) from the front panel


Relay

Quantity/type

8 normally open relays


Relay control connectors

(4) 3.5 mm captive screw connectors, 4 pole

Relay control contact rating

24 VDC, 1 A


eBUS

eBUS control ports

(1) 3.5 mm captive screw connector, 5 pole (uses 4 poles)

eBUS pin configuration

+V = +12 VDC; +S = + signal; -S = - signal; G = ground

Recommended cable type

Extron STP20-2/1000 or STP20-2P/1000 cable


Maximum system cable length

1000 feet (305 meters) sum total for the eBUS system, regardless of topology. Power injection may be required depending on system cabling topology and primary power supply wattage. See the eBUS Technology Reference Guide for details.


eBUS power output

12 watts


Switched DC power output

Quantity/type

4 switched 12 VDC outputs


Connectors

(4) 3.5 mm captive screw connectors, 2 pole


Power

Maximum 40 watts total


Power sense

Range

0.1 watt to 40 watts


General

Power supply

Internal

Input: 100-240 VAC, 50-60 Hz


Power consumption

TBD watts


Temperature/humidity

Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing


Cooling

Convection, no vents


Thermal dissipation

TBD BTU/hr


Mounting

Rack mount

Yes, with optional 1U rack shelf


Furniture mount

Yes, with optional bracket kit


Enclosure type

Metal


Enclosure dimensions

1.7" H x 8.7" W x 10.5" D (1U high, half rack wide)

(43 mm H x 221 mm W x 267 mm D)

(Depth excludes connectors.)


Product weight

TBD lbs (TBD kg)


Regulatory compliance

CE, C-Tick, c-UL, FCC Class A, ICES, UL, VCCI

Complies with the appropriate requirements of RoHS, WEEE


Product warranty

3 years parts and labor


Everlast power supply warranty

7 years parts and labor


NOTE

The 5-pole ports support both hardware and software flow control.

The 3-pole ports support software flow control.

The default for both types of ports is no flow control.


NOTE

All nominal levels are at ±10%.


NOTE

Specifications are subject to change without notice.

KUNTA-AV%20LOGO-me.png

Yh­teys­tie­dot

KUNTA-AV


info@kunta-av.fi

kunta-av.fi


Ritalankatu 31

33400 Tampere

© Coaxial  OY 2020